No products
This tubing is resistant against pH up and down and handles nutrients...
The Controllable Power Outlets switch on and off the hardware in the...
The Humidity Sensor is a relative humidity (%RH) and temperature sensor....
Keeping your nutrients and pH levels perfect all the time is one of the...
This unit allows for a low voltage power supply to be switched on and...
The Growtronix Automation System allows for precision control over every...
This sensor is inserted into the medium (soil, rockwool, coco, etc) and...
The Add-on Network Interface Module (NIM) can be added to a base system...
This sensor allows for monitoring the water/nutrient level of the...
This tubing is resistant against pH up and down and handles nutrients very well. Sold by the foot.
The Controllable Power Outlets switch on and off the hardware in the growing area. Such as ventilation blowers, pumps, lights, dehumidifiers, fogger/humidifier, water chillers, heaters, fans, or just about any other electrical device.
The Humidity Sensor is a relative humidity (%RH) and temperature sensor. As with all Growtronix Sensors, the sensor value can be used to preform actions such as turning on a fan or dehumidifier and/or sending a text message to alert of a high or low humidity levels.
Keeping your nutrients and pH levels perfect all the time is one of the secrets to a huge harvest. The dosing pump gives you complete control of your nutrients. Even when you can't be there to do it directly. Set a schedule so that the nutrients are automatically added in the correct amounts to maintain the perfect EC/TDS and pH from week to week.
This unit allows for a low voltage power supply to be switched on and off at it's two outputs. Each output is independently controllable in the Growtronix software. For example you could plug in a 12v power supply into the input then plug the output into a 12v solenoid valve to be able to control (open and close) the valve.
Elevating CO2 levels in your growing area is an easy way to maximize your harvest. For plants CO2 is food. There is CO2 in the air that plants use but raising the levels makes your plants grow as quickly as their genetics will allow. Our CO2 Sensor reads levels between 0-5000 PPM.
The Growtronix Automation System allows for precision control over every aspect of the growing environment. The base system is a starting point, it contains all the essential hardware and software for setting up a basic control system.
This sensor is inserted into the medium (soil, rockwool, coco, etc) and gives an extremely accurate soil moisture reading. Currently the software is setup to output a 0-100% soil moisture reading. This reading can be calibrated for your specific soil so that 100% is your soil fully saturated and 0% being completely dry.
The Add-on Network Interface Module (NIM) can be added to a base system to allow for adding an additional 32 hardware items to the network. This module can only be added to a base system, it can not act as a base system itself. A base system can support up to 15 add-on NIM's. Each NIM itself can support up to 500' of cable (with up to 32 hardware items...
This sensor allows for monitoring the water/nutrient level of the reservoir and can be utilized in many ways. Anything from total control of a reservoir by using Growtronix Controllable Power Outlets to turn on pumps when the reservoir is low to just a simple text message letting you know that the reservoir is running low.
The Growtronix Temperature sensor allows for precise temperature readings.
This unit is the same as our Controllable outlets unit but it has multi-national outlets that can accommodate power plugs from most countries. This allows you to just plug your equipment right in.
This module reads a 0-5 volts DC signal. It can be used to interface any sensor or module that has an analog output in the 0-5vdc range to the Growtronix system. This sensor can also be setup to read a 4-20mA or 0-20mA signal.
The Reservoir / Soil Temperature Sensor is an epoxy resin sealed waterproof temperature sensor. It can also be used as an outdoor/indoor temperature sensor.
This unit has two outputs Light and No Light. This is a custom unit and generic product label. Many controllers rely on a light sensor to know when the lights are on and off, the Growtronix system is aware of this automatically and doesn't require a light detector for most controls. However this sensor is handy for detecting a light which has been left on...
The Flood/Leak Detector is a sensor no hydroponic grower should go without. It is capable of detecting 1/16" of water. The Growtronix software can be setup to turn off pumps or close valves and send you an email or text message to your cellphone. We have received some great stories of this sensor saving people from a lot of grief. We highly recommend this...
This sensor is fairly self explanatory, It lets the software know whether a door or window is open or closed. The part of the sensor which extends from the unit is attached on one side of the door and the other module (an enclosed magnet) is attach on the other side. If the gap between these two modules is more than about 1" the software is told that it...
3 Foot unshielded cable. The Growtronix system uses standard cat5e cables. We recommend purchasing from IOFast.com
The float sensor allows for monitoring the water/nutrient level of the reservoir and can be utilized in many ways. Anything from total control of a reservoir by using Growtronix Controllable Power Outlets to turn on pumps when the reservoir is low to just a simple text message letting you know that the reservoir is running low
**This item is currently out of stock ** The Smoke Detector is a silent photoelectric smoke detector with a Growtronix Interface. The Growtronix software can be setup to turn off all power to the outputs, send a text message and/ or Play a sound file.
Monitoring and controlling pH has never been easier! The importance of controlling pH in an indoor garden can't be overstated. The pH of the nutrient solution determines how available the nutrients are to the plants. Too high and several nutrients are unavailable, too low and several other nutrients become unavailable.
This sensor allows the Growtronix system to detect motion, it's generally used as part of a personal security system.You can easily setup the system to text message your cellphone if a break in occurs. You can also play a sound file and/or save snapshots from an installed camera.
10 Foot unshielded cable. The Growtronix system uses standard cat5e cables. We recommend purchasing from IOFast.com
